used equipment for sale
CONCRETE BULL FLOAT WITH 5' HANDLE
The bull float is perfect for floating large slabs of concrete such as driveways and patios. Includes a 48 magnesium bull float with round ends and a 5' handle. Lightweight float and handle allow for a tool that is easy to control even when a long reach is required. Additional handles available in easy to add in 5' lengths.
CONCRETE EDGER FLOAT
This concrete finishing tool is used to form a clean edge along newly poured concrete. Offers an inexpensive way to neatly finish the edges of your slab for a more professional look. Turned up end prevents unsightly indentations as you slide along the edge of your slab.
CONCRETE HAND FLOAT
Smooth magnesium body allows you to produce a level surface and a clean finish on your newly poured concrete. In areas too small for the bull float, the hand float does the job. Easy to use and inexpensive to rent, the concrete hand float allows you finish your pour professionally
The jitterbug tamper is the easiest to use concrete tamper on the market. It is ideal for all finishes: exposed aggregate, float, broom, trowel, or as a key for two course work. Excellent for depressing exposed aggregate into wet cement for a smooth finish.
Spreads grades smoothes & floats concrete. Constructed with 14-gauge cold-rolled steel and 54" long hard oak handle. The blade size is 20" x 4. Ideal for spreading concrete to the edges of your form.
The gasoline powered surface grinder features 6 grinding stones that are typically used for light concrete grinding applications. Normal applications include removing a broom finish or smoothing high spots. Can remove up to 1/4" of concrete from the surface- effectiveness can depend how much aggregate is present in your concrete.
CONCRETE MIXER, 2 CUBIC FOOT (ELECTRIC)
The lightweight, polyethylene drum on this two-wheel mixer allows you to work almost anywhere. It will mix approximately 1.5 cubic feet of ready-mix concrete. This is equal to about 1.5- 80 lb. bags of ready-mix concrete, or 2- 60 lb. bags of ready-mix.
CONCRETE MIXER, 9 CUBIC FOOT (GAS)
Large heavy duty side dump mixer. A generous 9 cu. ft. capacity for large batches. Approximately 8- 80 lb. bags of ready-mix concrete capacity. (Equal to 10 to 11- 60 lb. bags of ready-mix) Big 36" diameter thick steel drum. Requires a 2 inch ball to tow.
Surface planers are ideal for removing trip-and-fall hazards, stripping thick, high tensile floor coatings or profiling any surface for a new coating. Specially designed carbide flails can effectively remove thermo and cold plastic type markings from streets and industrial floors. Set of teeth (required) can be purchased.
CONCRETE SAW, 14"
The 14" concrete saw is used for a variety of purposes that require concrete to be cut and removed. They are engineered for operators from DIY to professional that demand quality, ease of operation and accurate sawing. Cuts up to 5.5" deep and is available with disposable or a diamond blade.
CONCRETE SAW, 18"
An exceptional saw for its size, the 18" concrete saw is built to cover a wide range of cutting applications. Offers accurate sawing and operator comfort. Cuts up to 7.5" deep and is available with disposable or a diamond blade.
CONCRETE SAW, RING TYPE
The ring saw is the world's first gas-powered cutter able to make 10" deep cuts with a 14" blade. This may seem impossible to anyone who uses standard power cutters, since 14" blades can normally only achieve a cutting depth of 5". The blade is driven from the periphery instead of its center. With the ring saw, you can have the best of both worlds: the tried and tested ringsaw technology with its incredible cutting depth, and the ease of use and versatility of a gas-powered cutter.
CUTOFF SAW, 12" ELECTRIC
5000 RPM saw is used for a variety of metal and masonry cutting applications. Cuts up to 3.5" deep and is available with disposable blades (for masonry or metal cutting), or a diamond blade for masonry cutting.
CUTOFF SAW, 12" GAS
Weighing in at just 20.8 lbs, the 12" gas cutoff saw is the dependable and easy to use choice of professionals everywhere. The shock absorbing starter, anti vibration system, and convenient throttle trigger interlock functions are designed with the operator in mind. Available with your choice of disposable blade for a variety of applications or a diamond blade for masonry cutting.
CONCRETE VIBRATOR, BATTERY POWERED
Concrete contractors will appreciate this unique 12V cordless concrete vibrator. This lightweight, portable unit produces a consistent finish on concrete footings and walls without the hassle of dragging heavy electrical or gas units all over the jobsite.
CONCRETE VIBRATOR, REGULAR
On-site vibration of concrete for foundations, walls, columns and slab work. In plant vibration of concrete during the production of pipes, slabs, beams, double T's, columns and walls.
The core drill for vertical or horizontal boring and has the capability to drill through an 8 inch foundation wall. It can also drill through floors with the supplied vacuum capability or through walls if mounted with a 1/2" wall anchor. Leaves a smooth edged round hole for installation of pipes, posts, etc. 1", 2", 2.5", 3", 3.5", 4", 4.5", 5", 6", 8" or 10" bits available- priced separately.
CORE DRILL, HAND HELD
Designed to bore through concrete slabs or walls, the hand held core drill is lighter, easier to transport and simpler to operate than a stand-mounted unit. Drill unit without bit weighs 15 lb. Drill has a 3 speed motor and a variable speed trigger for better control. 15 amp motor will likely require a 20 amp circuit to operate. Water inlet with hose bib is intended for lubrication, cooling and dust control. It must be used with this drill. Drill is available with 1", 2", 2.5", 3", 3.5", and 4" core bits, which are rented separately at additional charge.
Designed to transport concrete and other materials across job sites for convenience. Pivoting dump allows for easy exit of material. Stand-on design allows for unobstructed view of the work site. Compact design allows for direct delivery of concrete to forms in hard to reach areas. Will fit though a 48" opening. Buggy can handle up to 2500 lb of concrete (16 cubic feet).
HAMMER, 60# ELECTRIC BREAKER
This plug in anywhere hammer is a favorite among the rental industry for its term sustained durability and minimal down time. Requires 15 amps and you are limited to a maximum of 50' of 12 gauge cord to prevent damage to the breaker. Available with a point, narrow chisel, 3" chisel, asphalt spade, or clay spade.
HAMMER, 60# GAS BREAKER
The 60 pound gas breaker is great for working in areas where air compressors or electric power is not available. Runs on standard gasoline with oil mixture (50:1 Ratio). Uses include breaking concrete, rocks, driving ground rods, tent stakes, etc. Available with a point, narrow chisel, 3" chisel, asphalt spade, or clay spade.
HAMMER, 15# AIR CHIPPER
This hammer is a four bolt design which reduces handle breakage and offers extra strength and better grip. This unit measures just under 16" long and weighs in at 19 lbs. Ideal for chipping on a wall, overhead, or in confined areas. The air chipper is available with a point or narrow chisel.
HAMMER, 30# AIR BREAKER
The 30 lb air breaker allows for easy handling invertical and horizontal positions. Requires our tow behind air compressor to run effectively. Available with a point, narrow chisel, or 3" chisel.
HAMMER, 60# AIR BREAKER
This 60 lb air breaker is excellent for breaking asphalt, concrete and brick. This middle sized air breaker can be used on many different applications. Requires our tow behind air compressor to run effectively. Available with a point, narrow chisel, 3" chisel, asphalt spade, or clay spade.
HAMMER, 90# AIR BREAKER
This 90 lb air breaker breaks aggregate concrete, slag or foundation removal. This is our largest air powered breaker suitable for the tougest jobs. Requires our tow behind air compressor to run effectively. Available with a point, narrow chisel, 3" chisel, asphalt spade, or clay spade.
Scabblers use compressed air to hammer piston-mounted bits into the concrete surface roughening the concrete surface more than grinding or scarifying. The scabbler can remove up to 1/4 inch of concrete surface in a single pass. The actual production rate depends on the strength of the concrete. A typical removal rate for a machine with a 12-inch working width is 200 to 250 square feet per hour at a 1/8-inch depth. Used for breaking up blistered or spalling concrete, removing floor coatings, or roughing surface to create a bond for overlays.
TROWEL MACHINE, 36"
The 36-inch inch trowel machine is popular mid-size trowel. Reliability and performance are trademarks of this industry-proven trowelunit. It is powered by a 5 horsepower Honda and operates with a 115 max rotor rpm making it ideal for smooth finishes. Available with quick pitch handle for blade adjustment.
TROWEL MACHINE, 46"
The 46-inch ring diameter trowel and a 60-130 rotor rpm is designed for contractors to get maximum coverage and the quality finish they expect. Powered by a 9 horespower Honda engine and available with your choice of a quick pitch handle for blade adjustment.
20 FOOT STORAGE CONTAINERS
We rent 20 foot secure storage containers. For more information, click on the link below. Or give us a call at 225-291-1356.
USED EQUIPMENT FOR SALE
© 2010 AAA Rent-All : All Rights Reserved.
Site Designed by
Baton Rouge Web Design Firm
Powered by the Website Gadget Content® Management System